3
PipeWorx Welding System (Continued)
Right-sized power source provides 400 amps at
100 percent duty cycle for Stick for maximum
stick electrode diameters. Provides 350 amps at
100 percent duty cycle for TIG welding in high-
amperage applications. Provides 400 amps at
100 percent duty cycle for MIG and gas-shielded
Flux-Cored weld processes.
Feeder Cart #300 467
For remote feeder applications. Includes cable
hangers and consumables drawer.
Bernard
™
PipeWorx guns
configured for pipe
welding applications.
PipeWorx Running Gear
#300 368
Includes dual gas cylinder rack
and front handles for power source.
Single or dual wire feeder available
with simple operator interface. Wire
feed speeds up to 780 IPM.
Composite Cable Kit
#300 454 25 ft. (7.6 m)
#300 456 50 ft. (15.2 m)
For remote feeder
applications.
Encases
control cable, weld cable and
gas hose in a protective sheath
to simplify installation and
reduce clutter in the weld cell.
RFCS-14 HD Foot Control #194 744 (Optional)
For TIG applications.
Heavy-duty foot pedal
current/contactor control with increased stability
and durability from larger base and heavier
cord. Reconfigurable cord can exit front, back
or either side of the pedal for flexibility. Includes
20-foot (6 m) cord and 14-pin plug.
Cable hangers are provided with the power
source for guns, Stick electrode holders and
TIG torch.
PipeWorx Remote Feeder Interface #300 597
Designed for manipulators and other mechanized devices used to hold the torch in roll-welding
applications. It features a simple operator interface with LEDs for easy viewing.
1. MIG Process Type Indicator is helpful in remote feeder applications.
2. Jog feeds the wire through the torch.
3. Trigger Hold reduces welder fatigue by allowing continuous welding without holding the trigger.
4. Remote Memory Select allows the welder to change programs (stored parameters) without
returning to the power source or feeder.
5. Purge purges gas hoses.
6. Left and Right Gun Triggers
Rear Panel of Feeder
Volt Sense Lead Connection—This provides
accurate voltage feedback for proper operation of
the MIG Welding Processes.
Note: The arc will be hotter than typical welding
systems at a given setting because the voltage
loss in the weld cable is not included in the
measurement displayed on the meter.
1
4
5
6
2
3
Additional Accessories
Spool Covers —
for 12-inch (305 mm)
diameter spools
#057 607 For single or
left side of dual feeder
#090 389 For right
side of dual feeder
Protects wire from dust and contaminants.
Reel Covers — for 60-pound (27 kg) coils
#195 412 For single or left side of dual feeder
#091 668 For right side of dual feeder
Protects wire from dust and contaminants.
Wire Reel Assembly
#108 008
For 60-pound (27 kg) coil
of wire.
DSS-9 Dual Schedule
Switch #071 833
Allows the operator to
switch between two sets
of parameters during welding to provide
consistent penetration in the fixed position
or change parameter between passes in roll
welding applications.
RPBS-14 Remote Control
#300 666
Attaches to the TIG torch
to remotely start and stop
the TIG welding process.
Wireless Remote
Foot Control
#300 429 For PipeWorx models with serial
number MA470021G and after
#300 859 For PipeWorx models before
serial number MA470021G
See Lit. Index No. AY/6.5 for more information.
(40 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals