Miller PipeWorx 400 Owner's Manual Page 21
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
OM-253 906 Page 15
SECTION 4 − SPECIFICATIONS
4-1. Important Information Regarding CE Products (Sold Within The EU)
A. Information On Electromagnetic Fields (EMF)
! This equipment shall not be used by the general public as the EMF limits for the general public might be exceeded during welding.
This equipment is built in accordance with EN 60974−1 and is intended to be used only in an occupational environment (where the general public
access is prohibited or regulated in such a way as to be similar to occupational use) by an expert or an instructed person.
Wire feeders and ancillary equipment (such as torches, liquid cooling systems and arc striking and stabilizing devices) as part of the welding
circuit may not be a major contributor to the EMF. See the Owner’s Manuals for all components of the welding circuit for additional EMF exposure
information.
S The EMF assessment on this equipment was conducted at 0.5 meter.
S At a distance of 1 meter the EMF exposure values were less than 20% of the permissible values.
ce-emf 1 2010-10
B. Information On Electromagnetic Compatibility (EMC)
! This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low−
voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations, due to con-
ducted as well as radiated disturbances.
This equipment complies with IEC 61000−3−12 provided that the short−circuit power Ssc is greater than or equal to 9,138,888 at the interface
point between the user’s supply and the public system. It is the responsibility of the installer or user of the equipment to ensure, by consultation
with the distribution network operator if necessary, that the equipment is connected only to a supply with a short−circuit power Ssc greater than
or equal to 9,138,888.
ce-emc 1 2011-09
4-2. General Specifications
A. Welding Power Source Specifications
Input
Power
Welding
Process
Rated Welding
Output
Amperage
Range
Setting (CC
Process)
Voltage
Range
Setting (CV
Process)
Maximum
Open-
Circuit
Voltage
DC
Amperes Input
At Rated Load
Output
50/60 Hz,
Three-Phase
KVA KW
380 V 400 V 380 400 380 400
Three
Phase
Stick
400 A @ 36 Volts
DC, 100% Duty
Cycle
40 − 400 — —
90
26.3 25.5 17.6 17.8 16.5 16.5
TIG
350 A @ 24 Volts
DC, 100% Duty
Cycle
10-350 — — 19.0 18.1 12.4 12.5 9.7 9.8
MIG
400 A @ 34 Volts
DC, 100% Duty
Cycle
— — 10-44 27.1 25.7 18 18 15.5 15.6
Flux
Cored
400 A @ 34 Volts
DC, 100% Duty
Cycle
— — 10-44 27.1 25.7 18 18 15.5 15.6
To appropriately size circuit protection see Section 5-10.
- PipeWorx 400 1
- Welding System 1
- From Miller to You 2
- DECLARATION OF CONFORMITY 3
- TABLE OF CONTENTS 5
- 1-1. Symbol Usage 7
- 1-2. Arc Welding Hazards 7
- NOISE can damage hearing 8
- BATTERY EXPLOSION can injure 9
- 1-6. EMF Information 10
- 2-1. Symboles utilisés 11
- L’EXPLOSION DE LA BATTERI 14
- OM-253 906 Page 10 16
- SECTION 3 − DEFINITIONS 17
- SECTION 4 − SPECIFICATIONS 21
- Work like a Pro! 22
- SECTION 5 − INSTALLATION 24
- 15 VOLTS DC 25
- ! Turn Off welding power 26
- Meters Per Minute (MPM) 27
- 254 085-A 29
- 254 087-A 30
- . Be sure that wire spools 31
- Elec Serv 2011−04 32
- OM-253 906 Page 27 33
- Input3 2011−03 − 254 080-A 34
- 805 302-A / 805 292-A 36
- 805 148-B / 805 141-A 37
- Ref. 239 780-B 38
- 805 030-A 38
- ! Turn off power before 39
- ! Do not use worn, dam 39
- 803 778-B 40
- On Power Source 41
- 254 086-A 42
- 5-21. Gun Trigger Receptacle 44
- A. Ideal Setup 46
- B. Bad Setup 47
- 805 291-B 48
- 805 294-A 49
- 805 295-A 50
- 805 296-A 51
- 254 084-A 52
- SECTION 6 − OPERATION 53
- A. Front Panel Controls 55
- 6-3. Memory Card Slot 56
- B. Using Optional Memory Card 57
- C. Memory Locations 57
- E. TIG Sequence Controls 58
- 6-4. TIG Sequence Control 61
- Ref. 252 613-B 62
- 252 613-B 64
- 6-9. Wire Feeder Controls 66
- 252 620-C 69
- 7-1. Routine Maintenance 79
- A. Required Equipment 80
- B. Calibration Procedure 80
- ! Significant DC voltage can 82
- Display Example 83
- 7-11. Cooler Troubleshooting 88
- OM-253 906 Page 83 89
- OM-253 906 Page 84 90
- OM-253 906 Page 85 91
- OM-253 906 Page 86 92
- OM-253 906 Page 87 93
- SECTION 9 − HIGH FREQUENCY 94
- Best Practices Followed 95
- SECTION 10 − PARTS LIST 96
- OM-253 906 Page 91 97
- SCR1,... 98
- OM-253 906 Page 93 99
- . Hardware is common and 100
- OM-253 906 Page 95 101
- OM-253 906 Page 96 102
- OM-253 906 Page 98 104
- OM-253 906 Page 99 105
- OM-253 906 Page 101 107
- OM-253 906 Page 104 110
- OM-253 906 Page 108 114
- Effective January 1, 2012 115
- For Service 116
- Owner’s Record 116
Related products and manuals for Welding System Miller PipeWorx 400
Welding System Miller RPC-IP User Manual
(20 pages)
(20 pages)
Welding System Miller Non-CE Owner's Manual
(48 pages)
(48 pages)
Welding System Miller Non-CE Owner's Manual
(88 pages)
(88 pages)
Welding System Miller Econotig User Manual
(40 pages)
(40 pages)
Welding System Miller SP-2 Specifications
(150 pages)
(150 pages)
© 2020, manymanuals.com. All rights reserved. | 0.227 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals