Miller Econotig Owner's Manual

EconotigRDescriptionArc Welding Power SourceProcessesGas Tungsten Arc(TIG) WeldingShielded Metal Arc(Stick) WeldingOM-303 155 795PSeptember 2003Visit

OM-303 Page 6Revenez à la table des matièresLe rayonnement de l’arc génère des rayons visibles etinvisibles intenses (ultraviolets et infrarouges) sus

OM-303 Page 7Revenez à la table des matières2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien del’appareil.Risque D’I

OM-303 Page 8Revenez à la table des matières2-4. Principales normes de sécuritéSafety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1,de l

OM-303 Page 9Return To Table Of ContentsSECTION 3 − DEFINITIONS3-1. General Precautionary Label

OM-303 Page 10Return To Table Of Contents3-2. Symbols And DefinitionsTig WeldingRemote Foot/HandControlStick Welding High TemperatureOutput Alternatin

OM-303 Page 11Return To Table Of Contents4-2. SpecificationsA. 60 Hertz ModelsRated Output at 20%Duty CycleWelding Amperage RangeAC High AC Low

OM-303 Page 12Return To Table Of ContentsSECTION 5 − INSTALLATION5-1. Selecting a LocationST-158 075Position unit so air can circulate.For information

OM-303 Page 13Return To Table Of Contents5-3. Typical TIG Connections Ref. ST-157 858-AY Turn Off power before mak-ing connections.1 Remote Control2 T

OM-303 Page 14Return To Table Of Contents5-4. Electrical Service GuideS-0092J. For 230 V models with wall receptacle, 100% duty cycle used to calculat

OM-303 Page 15Return To Table Of ContentsSECTION 6 − OPERATION6-1. ControlsRef. ST-155 790-F1 Weld Process SwitchUse switch to select weld process.In

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-303 Page 16Return To Table Of Contents6-2. Example of Front Panel Amperage ControlIn Example:Range = DCPercentage of Range = 50%Weld Amperage = 33

OM-303 Page 17Return To Table Of Contents6-4. Process and Material Thickness Guide LabelGuideline For Welding Process And Output For MaterialMaterial

OM-303 Page 18Return To Table Of ContentsSECTION 7 − MAINTENANCE AND TROUBLESHOOTING7-1. Routine MaintenanceY Disconnect power before maintaining.. M

OM-303 Page 19Return To Table Of ContentsSECTION 8 − ELECTRICAL DIAGRAMSSB-154 141-CFigure 8-1. Circuit Diagram

OM-303 Page 20Return To Table Of ContentsSECTION 9 − HIGH FREQUENCY9-1. Welding Processes Requiring High Frequencyhigh_freq1 11/96 − S-06931 High-Freq

OM-303 Page 21Return To Table Of Contents9-3. Correct Installation1 High-Frequency Source (welding powersource with built-in HF or separate HFunit)Gro

OM−303 Page 22Return To Table Of ContentsSECTION 10 − PARTS LISTST-801 399-C. Hardware is common andnot available unless listed.1234 56789101112131415

OM-303 Page 23Return To Table Of ContentsDescriptionPartNo.Dia.Mkgs.ItemNo.Figure 10-1. Main AssemblyQuantity1 154 335 BEZEL, front 1. . . . . . . .

OM−303 Page 24Return To Table Of ContentsDescriptionPartNo.Dia.Mkgs.ItemNo.Figure Figure 10-1. Main Assembly (Continued)Quantity42 PL1 157 958 LIGHT,

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 8/03Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA  2003 Miller Electric Mfg. Co. 1/03Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 US

OM-303 Page 1Return To Table Of ContentsSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _8/031-1. Symbol UsageMeans Warning! Watch Out! There ar

OM-303 Page 2Return To Table Of ContentsArc rays from the welding process produce intensevisible and invisible (ultraviolet and infrared) raysthat can

OM-303 Page 3Return To Table Of Contents1-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install

OM-303 Page 4Return To Table Of Contents1-5. Principal Safety StandardsSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,from Amer

OM-303 Page 5Revenez à la table des matièresSECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANTUTILISATIONsom_fre 8/032-1. Signification des symbolesSign